Ionizing Bar

Discharge1 <1.5 sec for ±1000V to ±100V discharge @ 30cm (12”), 50 mm air jet spacing with min CDA 2 lpm/airjet
Balance Inherently self-balancing system <±25V over the length of the bar; maintain balance setting >6 months without cleaning in clean environments
MicroPulse high voltage technology
Range 150-2000 mm, application and specification dependent
Flexible and powerful setup
Unique corona wire design (no emitter points)

Balance <±25V over the length of the bar; maintains balance performance >6 months without cleaning (in an ISO 14644 Class 4 or better environment)
Performance 3.5 sec decay average @ 600 mm (typ) measured at 5711 AeroBar center and 25 mm straight air jet spacing, 18 l/m purging air, (250 mm long AeroBar), no laminar flow; setting 1 Hz, 100% output, CPM: balance <±10V; swing 100V pk-pk
Compact Size (150 or 250 mm length)
Unique corona wire design (no emitter points)
MicroPulse high voltage technology
Remotely mounted controller for 5711 AeroBar

Output Voltage 13.5 kV p-p (max), adjustable
Distance 150-1000 mm distance to surface; application & customer specification dependent
Ion Emission Modulated pulse (MP) technology
Balance Auto balancing system <±20V
ISO 14644-12 (0.01 µm particles) ionization and
ISO 14644 Class 1 (0.1 µm particles) cleanliness
Modulated pulse technology
Excellent lateral uniformity
Low field voltages
Air-assist capability
Optional software with easy-to-use interface with wide adjustability
Alarm output signal

Output Voltage 13.5 kV p-p (max), adjustable
Distance 150-1000 mm distance to surface; application & customer specification dependent
Ion Emission Modulated pulse (MP) technology
Balance Auto balancing system <±20V
ISO 14644-12 (0.01 µm particles) ionization and
ISO 14644 Class 1 (0.1 µm particles) cleanliness
Modulated pulse technology
Metal-free design “M”
Excellent lateral uniformity
Low field voltages
Air-assist capability
Optional software with easy-to-use interface with wide adjustability
Alarm output signal

Balance <±5V, Novx System; <±5V, Novx Inside; <±20V, Standalone
Discharge 15 sec (typ) with no air-assist measured @ 24” below AeroBar center
Ion Emission Modulated Pulse (MP) technology
±20V or better balance as standalone, or ±5V with Novx monitoring and feedback system
Compatible with ISO 14644-1 class 3 or better
Centralize power and control with widely adjustable software
Sensor input, FMS connection, alarms, power and communications are located on the same end of the bar
Available in 14 lengths, from 350-2350 mm

Discharge1 25 sec or less for ±1000V to ±100V discharge @ 24” with min 60 fpm airflow
Balance
±50V @ 24” measured directly below two opposite polarity emitter points (Model 5685 must be mounted at least 6” away from grounded surfaces for optimum balance performance)
IsoStat® technology
Steady-state DC ion emission for high ion density
Single-crystal silicon or titanium emitter points
Multiple lengths, including short 11 inch AeroBars

Output Voltage 0-20 kVDC, ±10% for each polarity on an individual AeroBar; positive or negative output levels can be adjusted separately through GUI
Operating Mode Pulsed DC, steady-state DC or standby
Complete integration with tool control system
Fully adjustable parameters for each AeroBar
Ion current monitoring
Several lengths available including 3 specifically designed for EFEMs
Single-crystal silicon emitter points

Output Voltage 0-20 kVDC, ±10% for each polarity on an individual AeroBar; positive or negative output levels can be adjusted separately with IR Handheld Remote
Operating Mode Pulsed DC, steady-state DC or standby
All parameters are held within the AeroBar; no controller required
Fully adjustable parameters for each AeroBar utilizing Pulsed DC or Steady-state DC modes
Several AeroBar lengths including three lengths specifically designed for EFEMs
Ion current monitoring
FMS alarm output
Single-crystal silicon emitter points

Products