Products

ESD Monitor

SCS manufactures three different ESD Event Detection Meters and Monitors that allow you to identify ESD incidents throughout your manufacturing process. There are two handheld meter models and a continuous monitoring device. All of which are designed to detect and count ESD events that can damage sensitive components and cause tool lockups, erratic behavior and parametric errors. Once you can detect ESD Events, you can carry out diagnostics to determine what is causing them, and then you can put a solution in place. 

724 – Workstation Dual-Wire Monitor

  • Single workstation continuous monitor – Meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Continuously monitors 2 operator dual-wire wrist straps and 1 worksurface mat – Visible and audible alarms indicate improper grounding of the operator and worksurface
  • Adjustable operator test voltage and upper limit – Test voltage can be set to 9 or 16 volts; test limit can be set to 10 or 35 megohms
  • Adjustable audible alarm -Buzzer volume may be disabled or set to loud or soft
  • Simple installation and setup
  • Mounting hardware and wire management clips are included
Download Datasheet

725 – Portable Wrist Strap Monitor

  • Continuously monitors 1 operator dual-wire wrist strap and 1 ground connection
  • Visual and audible alarms indicate proper grounding of the operator and ground point
  • Compact size and 9 volt battery power supply
  • Monitor may be setup in areas where AC power is not available
  • 10mm ground snap located underneath the monitor
  • Monitor can provide ground to a portable worksurface when connected via the 10mm snap
  • 725VK Verification Kit sold separately
  • Use to perform periodic calibration testing of the 725 Wrist Strap Monitor
Download Datasheet

773 – Wrist Strap and Ground Dual-Wire Monitor

  • Single Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators and one conductive or dissipative worksurface; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Digital Signal Processing Technology
  • Provides stable continuous monitoring (versus pulsed or intermittent) of the wrist strap’s path-to-ground and the presence of its 1 megohm safety resistor
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item
  • 0.40 Volt Operator Test Voltage
  • Reduces the risk of electrical overstress (EOS) for the handling of sensitive components
  • 500 Millisecond Alarm Response Time
  • Identifies failures and intermittencies that inferior technologies miss
  • Operator Remote Disconnect Alarm
  • Prevents tampering should one intentionally disconnect the operator remote from the monitor
  • Miniature Monitor Size (0.85 x 2.4 x 2.6 inches)
  • Occupies minimal space and includes mounting tabs secure installations
Download Datasheet

770044 – GROUND MASTER MONITOR, ETHERNET

  • NEW 7-24VDC Power Input Terminals
  • Pairs with voltage sources commonly found inside machinery and eliminates the need for a power adapter
  • Equipment Ground Continuous Monitor
  • Continuously monitors the path-to-ground impedance of eight metal tools; meets ANSI/ESD S20.20.
  • Ethernet Connectivity
  • Provides communication with Static Management Program (SMP). Data collected through SMP includes metal ground impedance and EMI voltage.
  • Optical Relay
  • Pairs with lights and buzzers for increased visibility.
  • EMI Monitoring on Metal Grounds
  • Alarms if the grounded metal tools have high-frequency noise that could cause electrical overstress (EOS) damage.
  • Calibration Verification
  • NIST Calibrated with Certificate Included
  • 100-240VAC Power Adapter with Interchangeable Plugs
Download Datasheet

770049 – COMMON POINT GROUND MONITOR

  • AC Outlet Continuous Monitor
  • Continuously monitors the path-to-ground integrity of the outlet; meets the ANSI/ESD S6.1 requirement for verifying wiring orientation
  • Visual Common Point Ground Indicator
  • Identifies a properly wired AC outlet that may be used for grounding purposes of an ESD Control Plan
  • Visual and Audio Fault Alarms
  • Alarms instantly when a failure occurs to alert operators and supervisors of a problem
  • Six Banana Jacks and Six Screws for #8 Ring Terminals
  • Provides numerous groundable points for wrist straps, mats, carts, tools, and other items. May also be connected to other grounding hubs (see item 770043).
  • Enclosure with Mounting Tabs
  • Allows the monitor to be placed away from the AC outlet and in areas of high visibility
Download Datasheet

770067 – WS Aware Dual-Wire Monitor with Standard Remotes and Ethernet Output

  • NEW SCS 770069 Power Relay Compatibility
  • Controls power to workbenches, hand tools, and other electronic devices dependent on the WS Aware Monitor’s status
  • Dual Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators, two conductive or dissipative worksurfaces, and two metal tools; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01.
  • Ethernet Connectivity
  • Provides network communication with Static Management Program (SMP). Data collected through SMP includes operator resistance, operator voltage, mat resistance, metal tool impedance and metal tool EMI voltage.
  • Digital Signal Processing Technology
  • Applies an ultra-low test voltage to the operator (0.05V) for the handling of sensitive components.
  • Operator Body Voltage Detection
  • Alarms if the operator generates or contacts voltage that would be dangerous to an ESD susceptible item.
  • EMI Monitoring on Metal Grounds
Download Datasheet

724 Plus Workstation Dual-Wire Monitor

  • Single Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators and one conductive or dissipative worksurface; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Digital Signal Processing Technology
  • Provides stable continuous monitoring (versus pulsed or intermittent) of the wrist strap’s path-to-ground and the presence of its 1 megohm safety resistor
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item
  • 0.40 Volt Operator Test Voltage
  • Reduces the risk of electrical overstress (EOS) for the handling of sensitive components
  • 500 Millisecond Alarm Response Time
  • Identifies failures and intermittencies that inferior technologies miss
  • Operator Remote Disconnect Alarm
  • Prevents tampering should one intentionally disconnect the operator remote from the monitor
  • Miniature Monitor Size (0.85 x 2.4 x 2.6 inches)
  • Occupies minimal space and includes mounting tabs secure installations
Download Datasheet

CTC061-3-242-WW – WS AWARE MONITOR

  • Dual Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators, two conductive or dissipative worksurfaces, and two metal tools; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Digital Signal Processing Technology
  • Applies an ultra-low test voltage to the operator (0.05V) for the handling of sensitive components
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item
  • EMI Monitoring on Metal Grounds
  • Alarms if the grounded metal tools have high-frequency noise that could cause electrical overstress (EOS) damage
  • System Includes Monitor and Two Remote Terminals
  • Monitor can be installed at eye level, and remote terminals can be mounted at desired locations up to 10 feet away.
Download Datasheet

CTC062-RT-242-WW – WS AWARE MONITOR

  • Dual Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators and four metal tools; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Digital Signal Processing Technology
  • Applies an ultra-low test voltage to the operator (0.05V) for the handling of sensitive components
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with voltage that would be dangerous to an ESD susceptible item
  • EMI Monitoring on Metal Grounds
  • Alarms if the grounded metal tools have high-frequency noise that could cause electrical overstress (EOS) damage
  • System Includes Monitor and Two Remote Terminals
  • Each remote terminal includes a monitored jack for operators and an unmonitored jack for visitors.
  • Relay Terminal
  • Outputs 0/20 mA logic level for relay input
Download Datasheet

CTC331-WW – Iron Man® Plus Dual-Wire Monitor

  • Single Workstation Continuous Monitor
  • Continuously monitors the path-to-ground integrity of an operator and conductive or dissipative worksurface and meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Electrical Overstress (EOS) Detection
  • Alarms if overvoltage (±5V or less) from a tool such as a soldering iron or electric screwdriver is applied to a circuit board under assembly
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with a voltage that would be dangerous to an ESD susceptible item
  • Digital Signal Processing Technology
  • Applies a low test voltage to the operator (0.40V) for the handling of sensitive components
  • Miniature Size (0.85” H x 2.4” W x 2.6” L)
  • Uses minimal workspace and includes mounting tabs for installation underneath table tops
  • Use with Dual-Wire Wrist Straps
  • Replaceable Dual-Wire Operator Jack
Download Datasheet

CTC334-WW – Ground Man Plus Dual-Wire Monitor

  • Equipment Ground Continuous Monitor
  • Continuously monitors the path-to-ground integrity of an operator and three metal tools; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01.
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with a voltage that would be dangerous to an ESD susceptible item.
  • Digital Signal Processing Technology
  • Applies a low test voltage to the operator (0.40V) for the handling of sensitive components.
  • Miniature Size (0.85″ H x 2.4″ W x 2.6″ L)
  • Uses minimal workspace and includes mounting tabs.
  • Use with Dual-Wire Wrist Straps
  • Replaceable Dual-Wire Operator Jack
  • Calibration Unit Available for Accurate Performance and Conformity Testing in the Field
  • NIST Calibrated with Certificate Included
  • 100-240VAC Power Adapter with Interchangeable Plugs
Download Datasheet

CTC337-WW – Wrist Strap and Ground Dual-Wire Monitor

  • Operator and Equipment Ground Continuous Monitor
  • Continuously monitors the path-to-ground integrity of two operators and one metal tool; meets ANSI/ESD S20.20 in accordance with ESD TR1.0-01-01
  • Operator Body Voltage Detection
  • Alarms if the operator generates or comes in contact with a voltage that would be dangerous to an ESD susceptible item
  • Digital Signal Processing Technology
  • Applies a low test voltage to the operator (0.10V) for the handling of sensitive components
  • Miniature Size (0.85” H x 2.4” W x 2.6” L)
  • Uses minimal workspace and includes mounting tabs for installation underneath table tops
  • Use with Dual-Wire Wrist Straps
  • Replaceable Dual-Wire Operator Jack
  • NIST Calibrated with Certificate Included
  • 100-240VAC Power Adapter with Interchangeable Plugs
Download Datasheet

CTM048-21 – EM Eye – ESD Event Meter

  • Detects, counts and measures ESD events that can damage ESD items and cause tool lock-ups, erratic behavior and parametric errors
  • Calculates event magnitude for Charged Device Model (CDM), Human Body Model (HBM) and Machine Model (MM)
  • Records all measurements to a microSD card for PC download
  • Touchscreen display provides intuitive user interface
  • Rechargeable lithium ion battery
  • Assembled in the United States of America with Globally Sourced Materials
Download Datasheet

Let's start a new project together!

Contact Us

Singapore | Malaysia | China

© 2024 Cesstech. All Rights Reserved.